Journal of Applied Mechanical Engineering

Journal of Applied Mechanical Engineering
Open Access

ISSN: 2168-9873


Citations Report

Citations Report - Journal of Applied Mechanical Engineering [97 Articles]

The articles published in Journal of Applied Mechanical Engineering have been cited 97 times by eminent researchers all around the world. Following is the list of articles that have cited the articles published in Journal of Applied Mechanical Engineering.

Tammas-Williams S, Todd I (2017) Functionally Graded Materials. InLaser-Based Additive Manufacturing of Metal Parts. CRC Press.

Karun AS, Pillai UT, Rajan TP (2017) Fabrication and Characterization of Functionally Graded Metal and Polymer Composites by Sequential and Centrifugal Casting Techniques (Doctoral dissertation, Cochin University of Science and Technology).

Todd I, Tammas-Williams S (2017) Functionally Graded Materials. InLaser-Based Additive Manufacturing of Metal Parts.

Karhadkar S, Kanetkar S, Pawar N, Mistry H (2018) CFD Analysis for computing Drag force on various types of blades for Vertical Axis Wind Turbine.

Asghar U, Aziz I, Sher F (2017) Modelling and simulation of flow induced vibrations in vertical axis wind turbine blade. InApplied Sciences and Technology (IBCAST).

Xiao Y (2017) Advance in Penny-shaped cracks of piezoelectricity. analysis. 90: 91.

Wright C(2015) Heat exchanger maintenance basics.

Wright C(2016) Monitoring the condition of a heat transfer fluid has pump benefits.

Nainar SMM, Begum S, Ansari MNM, Hoque ME, Aini SS, et al. (2014) Effect of compatibilizers on in vitro biocompatibility of PLA–HA bioscaffold. Bioinspired, Biomimetic and Nanobiomaterials 3: 208-216.

Jabbari AH, Sedighi M,Razeghi AM(2013)Optimization of Wire-Winding and Shrink-Fit Combination in Pressure Vessel Reinforcement. International Review of Mechanical Engineering (IREME) 7,549-555.

Urade SD, Bhope DV,  Khamankar SD (2015) Stress Analysis of Multilayer Pressure Vessel. J Appl Mech Eng 4: 2.

Sedighi M, Noorian MT,  Jabbari AH (2014). Effects of geometrical tolerances on residual stresses in a compound shrink fitted pressure vessel. International Journal of Advanced Design and Manufacturing Technology 7: 13.

Mostafa NH, Adel M (2012) Effect of Blade Angle on Cavitation Phenomenon in Axial Pump. J Appl Mech Eng 1: 2.

Xiong Bing, Chen Lingen, Ge Yanlin, Sun Fengrui (2014) Finite time thermodynamics analysis of internal reversible Otto cycles with variable processes. Power and Energy 35:166-171.

Memet F, Preda A (2015)A point of view on Otto cycle approach specific for an undergraduate thermodynamics course in CMU. In IOP Conference Series: Materials Science and Engineering IOP Publishing 95: 012063 .

Performance analysis of typical flue gas waste heat recovery system for large coal - fired power plant boilers - Energy saving 32:34-38.

Gong Shouwen, Chen Lingen, Sun Fengrui (2013) Analysis and optimization of the internal reversible Lenoir cycle performance with variable process. Energy saving 32: 22-26.

Ge Y, Chen L,  Sun F (2016). Progress in finite time thermodynamic studies for internal combustion engine cycles. Entropy 18: 139.

Vyankatesh BE,  Rajesh RK (2012) Efficient method of producing oval punching holes on sheet metal. J Appl Mech Eng 1:109.

Van Nguyen H (2014) Analysis of the factors affecting hybrid ground-source heat pump installation potential.

Relevant Topics